FieldPro Logo
HomeAbout_UsProductsInstructionsPricingContact_UsWarranty

40 lb Hanging Feeder

40 lb Feeder
  1. Find the center of the barrel and drill a small hole (approximately 1/8"). Align the center hole of the template that is provided with the small center hole in the barrel.
  2. Mark the three outside holes on the template and drill these with a 3/16" bit.
  3. Go back and enlarge the center hole to 2".
  4. Push the #10 x 3/4" machine screws with lock washer through the three outside holes from the inside of the barrel. Use another lock washer and #10 nut to hold these screws in place. (See diagram right)
  5. Take the plastic pipe fitting and place it through the 2" hole. Tighten the nut over the fitting. The threads should point to the outside of the barrel.
  6. Mount the timer on the bottom of the barrel using the #10 nuts and lock washers included with the hardware. This is normally done when the feeder is in the field

Hunter's Special

Hunter's Special
  1. Holds up to 100 pounds of feed.
  2. A funnel is installed in the feeder so that all the feed is used.
  3. This feeder includes a hanging chain and mounting brackets used to support the feeder from an overhead limb or support.
  4. All mounting holes are punched and mounting hardware is included.
  5. A galvanized lid keeps water out and increases feeder life. The lid is held in place by a spring on one side and chain on the other side. This allows for easy access to the feeder.
  6. The feeder is shown with a Game Feeder I timer, but is also available with a Game Feeder II or Game Feeder III timer.
  7. If an overhead support is not available, 9 foot by 1 inch legs are available to support the feeder.

100 lb Stand Feeder

Part # 16624L

100lb Feeder
  1. Holds up to 100 pounds of feed.
  2. Heavy duty metal container
  3. May be suspended from above or mounted on legs
  4. Heavy duty brackets allow the use of either 1-inch or 1.5-inch legs.
  5. A galvanized lid keeps water out and increases feeder life. The lid is held in place by a spring on one side and chain on the other side. This allows for easy access to the feeder.
  6. Uses either the Game Feeder I, Game Feeder II, or the Game Feeder III timer. Mounting hardware is pre-installed on the container.

200 lb Stand Feeder

Part # 30624L

200lb Feeder
  1. Holds up to 200 pounds of feed.
  2. Heavy duty metal container
  3. May be suspended from above or mounted on legs
  4. Heavy duty brackets allow the use of either 1-inch or 1.5-inch legs.
  5. A galvanized lid keeps water out and increases feeder life. The lid is held in place by a spring on one side and chain on the other side. This allows for easy access to the feeder.
  6. Uses either the Game Feeder I, Game Feeder II, or the Game Feeder III timer. Mounting hardware is pre-installed on the container.

300 lb Stand Feeder

Part # 55624L

300lb Feeder
  1. Holds up to 300 pounds of feed.
  2. Heavy duty metal container
  3. Heavy duty brackets allow the use of either 1-inch or 1.5-inch legs.
  4. A galvanized lid keeps water out and increases feeder life. The lid is held in place by a spring on one side and chain on the other side. This allows for easy access to the feeder.
  5. Uses either the Game Feeder I, Game Feeder II, or the Game Feeder III timer. Mounting hardware is pre-installed on the container.

Tailgate Feeder

Part # TG-1

Tailgate Feeder
  1. Feeder slips into receiver hitch on your vehicle.
  2. New electronic control regulates amount of feed dispensed and area of coverage.
  3. A cable is provided that runs from the motor to the cab of your vehicle, where it plugs into the cigarette lighter.
  4. A special patented rotor prevents grain from spilling when the motor is not turned on.
  5. Motor and control unit are available separately.

This feeder contains: Brackets, motor, 100 lb container, funnel, lid, wiring harness, electronic control, hardware.

PATENT # 5,143,289

Fish Feeder

Part # FF-1

Fish Feeder
  1. Holds up to 50 pounds of floating fish food.
  2. The timer is mounted in the barrel to protect it from moisture.
  3. Will float on either FL-1 floats or three 15" wheels
  4. Microprocessor controlled for accurate feed times and amounts.
  5. Amount of feed dispensed is adjustable from 2 to 4 pounds.
  6. One-year warranty.

The fish feeder provides an easy way to systematically feed fish in a pond without building a dock or having to mount the container. Since the feeder floats, changes in the water level of the pond will not affect it. The 16 gallon drum holds 50 pounds of floating fish food and is designed specifically to dispense this type of feed.

The time unit is mounted inside the top of the drum to make it easily accessible and as dry as possible. It is powered by one 6 volt spring top lantern battery. The operation of the unit is the same as the Game Feeder III. You may feed up to 8 times in one day and the amount of feed that is dispensed is adjustable.

BATTERY NOT INCLUDED